The Most Pervasive Issues In Change Door Lock
Reasons to Change Door Lock
You can change your door lock for a variety of reasons, from increasing the security of your home to re-decorating the entrance. It is also possible to change locks if your key gets stuck inside or is difficult to turn.
The process of changing your lock is an easy project that even beginner DIY homeowners can tackle. Gather the materials needed to begin.
Remove the lock from the old one.
Before installing a new lock it is essential to remove the old one from the door. This is important when you suspect that someone else may have a key to the house. It's an excellent idea after you've moved into your new house, had a break-in, or welcomed a roommate. The process is much easier than you might think and can be completed in only a few minutes.
Begin by removing the screws holding the deadbolt faceplate onto the frame of the door. To remove the faceplate, you'll need to remove screws on both sides. This will let you see what is behind it, and will provide you with a better understanding of how to proceed in the next steps.
After removing the faceplate you will have to remove the bolt as well as the strike plate and strike plate. Remove the bolt from the door hole using the screwdriver. If the bolt is rusted you may need to use a chisel to smash it. If you are using a chisel, you must be careful not to damage the door frame.
Make sure that the new deadbolt, doorknob and lock will fit in the holes that are already present in the door before you take out the old one. A lot of hardware stores and big box stores carry a variety of locks and will help you choose the right one. If the lock you bought does not match your door, send it back and seek assistance.
Find small depressions or notches inside the handle and around the trim while you remove the old lock. If you can find them, slide a straightened safety pin or a flat screwdriver into them to loosen the handle and expose the screws beneath.
Once the screw inside the handle has been removed you can begin removing the knob from its spindle. To do this, locate the set screw located at the base of the knob and loosen it. Then, you'll need to remove the knob from the spindle, and carefully remove the spindle from the door.
Install the new lock
It is a good idea to change the locks on your doors regularly, especially if you have had a break-in. It's easy, affordable and effective to change the lock on your door. Repair My Windows And Doors of people can do it yourself with a screwdriver and a few basic instructions. Depending on your situation you may need to learn how to change the key of a door lock so that only you own the key.
To begin the process, you'll need to buy a new lock that is compatible with the keyway on your existing lock. Locksmiths are usually able to replace your lock at a cost, but you can save money by doing this yourself. You can buy a new lock from a hardware store or on the internet. Standard deadbolts are suitable for most doors. However, you will need to measure your door to ensure that it is suitable.
Your new lock will often come with a template showing how to install it on the door. The template can be used to drill the hole. It is much easier than measuring every time. If the template doesn't line to the hole you intend to drill you need to return it to the hardware store and purchase another one.
It is essential to install the new lock on the right-hand side of the door. You can verify this by looking at the latch, which should be marked "up" or something similar. Make sure the latch is correctly seated on the plate and then attach it using the supplied screws.
When replacing a knob lock, you should also be aware of the handing. Most knob locks are left-handed, however, there are some that are right-handed. If you're not paying attention, the knob could be installed on the wrong side of your door, which could make it impossible to lock either from the inside or outside.
It is recommended to test the new lock after you have completed. You should be in a position to lock the door from both the inside as well as the outside, and unlock it with a key. If you are not satisfied with the result, you can call a locksmith to repair the issue.
Test the lock
A door lock that will not unlock can be annoying but it can also put your family's safety at risk. It's simple to solve the majority of problems with door locks by conducting some troubleshooting and lubrication. To start with, check that your key is correctly cut and that the lock itself isn't loose or dirty. If this doesn't fix the problem, you can try lubricating the door lock actuator with powdered graphite or a silicone-based grease.
Check that the door lock switch, wiring harnesses and actuator connector are all working properly. Check the wiring diagram or manual to determine the color-coding and the function of each door lock switch wire. Use a digital meter, or test light to determine if the actuator is receiving power and ground when the switches are turned on. If you observe a voltage toggle with each switch's activation, it means the switches are working and it's most likely the actuator that requires to be replaced.
If the switch seems to be working but the actuator does not move when you turn it, there may be a problem in the cylinder. The actuator cylinder has spring-loaded pins that prevent the cylinder from moving until the key is inserted, which moves the pins upwards to match the key's height in that location. The cylinder will then begin to turn and open the lock body, allowing the latch to open for the handle.
If the door lock actuator is still faulty, you can remove the switch and wires from the actuator with small screwdrivers to loosen the locking bolt and separate the plastic cover that houses the electrical connector. Then, disconnect the door lock actuator, and let it fall. Then, you should be able to find the two bolts of 10mm that keep the actuator in place and remove them. After the actuator is removed then you can disconnect the black electrical connector.
Replace the key
Whether you have a keyed deadbolt or door knob If it's not working properly you need to either change the lock's key or rekey it or replace it completely. It is not difficult to do it yourself and could save you a lot of money. It is recommended to hire an expert locksmith inspect the locks for any issues before you start. This will give peace of assurance that your home is secure and safe.
To begin, take off the exterior faceplate from the deadbolt or doorknob. If there are screws holding the faceplate, use a screwdriver and pull it off. Then, remove the interior faceplate by using a screwdriver with a flat head. After you have removed the faceplate, you can remove the bolt and screw from the lock cylinder.
A locksmith can determine whether you require a replacement or rekey the lock. They can also provide advice on the best security measures for your home. They will also make any necessary modifications to the door and frame to ensure a perfect fit. They also provide a warranty on their work.
You need to purchase a new lock key before you are able to change it. It is essential to use the lock key that is snugly fitted. A key that's not of the correct size could cause damage to the internal mechanism of the lock and hinder it from working. To test the size of a key, insert it into the lock. If it fits perfectly with the plug, it's of the correct size. If the pins protrude from the top of the plug and are not a good fit, they're too long.
There are a variety of reasons you might want to change your door lock, for example:
If you're moving into a previous owner's home or if you have lost keys, rekeying your lock can be a more affordable alternative than replacing it. It can also be more cost-effective than a complete replacement. However, there are some circumstances where rekeying your lock isn't feasible. If the lock has been damaged or repeatedly jammed, for instance it could be the right time to replace it.